雷竞技appFluke 773 milliamperes process clamp type table
The main features
雷竞技appThe function of the Fluke 773 mA clamp table:
- Better accuracy of 0.2%
- 0.01 mA sensitivity and resolution
- Without "disconnect circuit can measure 4 to 20 mA signal
- Measurement of PLC and analog I/O mA signal control system
- It can display mA measured value and the percentage of 4 to 20 mA range double backlit display
- Measuring spot light up the darkness is difficult to found inside the case
- With extension cords detachable clamp table, can be measured in the narrow space
- Use 99.9 mA range measurement control system of the old is 10 to 50 mA signal
- Automatically change 4 to 20 mA output for remote testing
- Automatically shut down, the power saving function such as backlight timeout can prolong battery life
- "Keep function can capture and display the measured value of the constantly changing
- Through the pens and "access circuit function measurement 4 to 20 mA signal
- Synchronous circuit power supply 24 v and measurement circuit of mA signal, can transport device for power supply and test it
- 4 to 20 mA output signal source to test the control system I/O or I/P
- MA output linear gradient or 25% output step by step
- Automatically change 4 to 20 mA output for remote testing
- Dc voltage measurement, can verify voltage 24 v power supply or the I/O signals
- To provide the dc voltage source to test an acceptable 1 or 0 to 5 v to 10 v signal input device
- Measured by the output ratio of mA and mA clamp table 4 to 20 mA signal corresponding to the continuous mA signal
- Record to separate the milliampere signal equipment, without having to disconnect the circuit
- MA signal output DMMS or other equipment to allow log 4 to 20 mA signal, without having to disconnect the circuit
- MA: input/output table of wire is used to measure the mA signal, and output mA signal source
- MA input signal is applied to equipment, and then on the equipment such as valves or mA isolator measure its 4-20 mA output
- Voltage output linear gradient or 25% output step by step
- The output voltage automatically change for remote testing
The spot
selections6829.00
Tax-inclusive price
Produc雷竞技appts overview: Fluke 773 milliamperes process clamp type table
Need more time?
When performing 4-20 mA signal measurement don't disconnect the circuit, and save time.
You are wasting valuable time?
- By removing the line and disconnect the circuit to perform the mA measurement
- Call control room to isolate circuits
- Test the analog input/output on the console
- Rule out with mA fault of input and output device
- Repair the intermittent problems or unstable 4-20 mA loop
- Return to shop for other tools
If you are always busy雷竞技app, never enough time, then try the Fluke 773 milliampere clamp type table.These pliers type table do not need to perform some time wasting activities, can greatly save time and money.Now, you don't have to disconnect the circuit or closed system, 4-20 mA loop can diagnose and repair.
Belo雷竞技appw is a Fluke 773 clip-on table can provide some help for you:
| Ma clamp table properties | application | How to save time and money |
| Without disconnect circuit measurement of PLC and analog I/O mA signal control system. | Measuring the weak direct current (dc) | Make the process instructions associated with real physical values |
| Don't need to disconnect the circuit can output signal transmission device | Without disconnect circuit maintenance and diagnosis process and automation equipment | Don't interrupt the process |
| With extension of detachable grips table | Measurement can be performed in a narrow space | Allow measurement in all sorts of difficult circumstances |
| Output, simulation and measurement circuit of mA signal (disconnect circuit) | Confirm the non-contact measurement.At hand have to deal with fault spare tools (source simulation) | After find bad signal through non-contact measurement, without return workshop for loop checking instrument for troubleshooting |
| VDC source output and measurement | Rule out the failure of voltage input and output devices. | Measuring whether there is a 24 v circuit power supply.Measurement of 1 to 5, or 0 to 10 v process signal. Test chart recorder |
| 4 to 20 mA, input/output | Used to deal with the failure of dual channel mA source and measurement | 4 to 20 mA signal transmission to the valve and mA signal conditioner, then synchronous measuring 4 to 20 mA, a control output signal. |
| 4 to 20 mA output | Measured by the output ratio of mA is used to represent mA mA signal output value | Without disconnect circuit connected with the function of recording/graphic DMMS (DMM) and record the mA signal |
| Provide circuit power | Power supply for transmission equipment | Replace the installed circuit of 24 v power supply test.For power supply and to measure its mA output signal transmitting device for troubleshooting. |
| Can display 4-20 mA mA measured value and the percentage range of double backlit display | Clear display measurement | Allow rapid measurement evaluation |
| Measuring the spotlight | Light in the darkness of the chassis is difficult to find | Measurement process easier and faster |
| In non-contact way maximum measuring current of 99.9 mA | The broad range | In the old control system of measuring 10 to 50 mA signal |
| Automatically shut off the power | Automatically shut down after 15 minutes and 2 minutes backlighting and spotlight | Extend the life of the battery |
Produc雷竞技appt specifications: Fluke 773 milliamperes process clamp type table
| Technical indicators | ||
| To measure the diameter of the conductor | 0.177 or 4.5 mm (maximum) | |
| Working temperature | - 10-50 DHS C | |
| Storage temperature | - 25 - DHS 60 C | |
| Working humidity | < 30 DHS when C < 90%, 30 to 55 DHS when C < 75% | |
| Work at an altitude of | 0-2000 m | |
| IP protection grade | IP 40 | |
| size | 44 x 70 x 246 mm (2 x 5 delighted many customers and 7/8 5/8 x 11 in) | |
| The weight of the | 410 g (14.4 oz) | |
| vibration | 2 grams, the randomness of 5 to 500 hz | |
| The impact | Except 1 m drop test (nip) | |
| EMI/RFI | In accordance with EN61326-1 | |
| Related with the current measurement of jaw clip, for 1 to 3 v/v/m m the EMC of magnetic field strength 1 ma to specifications. | ||
| The temperature coefficient of | DHS 0.01% C 18 DHS (< C or > 28 DHS C) |
|
| Power supply and battery life | (4) AA 1.5 V alkaline batteries, IEC LR6, 12 hours, mA output driver 500 ohms | |
| Warranty period | Three years of electronic products Cable and clamp table accessories warranty for one year |
|
| Functional specifications | ||
| MA measurement (measured by the clamp table) |
Resolution/range | 0 and 20.99 mA |
| precision | 0.2% + 5 words | |
| Resolution/range | 21.0 mA to 100.0 mA | |
| precision | 1% + 5 words | |
| MA measurement (measured with the test socket series) | Resolution/range | 0 and 24.00 mA |
| precision | 0.2% + 2 words | |
| MA output (24 mA mA driver: drive 1000 ohms) | Resolution/range | 0 and 24.00 mA |
| precision | 0.2% + 2 words | |
| MA simulation (maximum voltage 50 V dc) | Resolution/range | 0 and 24.00 mA |
| precision | 0.2% + 2 words | |
| The output voltage (2 mA drive current largest) | Resolution/range | 0 to 10.00 V dc |
| precision | 0.2% + 2 words | |
| Voltage measurement | Resolution/range | 0 to 30.00 V dc |
| precision | 0.2% + 2 words | |
Proc雷竞技appess models: Fluke 773 milliamperes pliers type table
雷竞技appFluke 773
Ma process clamp type table
Attachment:
- 4 AA alkaline batteries (installed)
- Soft portable package
- TL75 test line
- AC 72 detachable clamp
- TL 940 miniature hook test line
- The instructions
- With Velcro Velcro belt hanging tool
